Cold Flow additives

Cold Flow additives ZX-P2-02 contains highly efficient anticoagulant factors, which can effectively lower the freezing point of diesel and prevent it from solidifying at low temperatures. It can usually lower the freezing point of diesel by 10℃to 20℃.

In extremely cold weather, Cold flow improver and pour point depressant for middle distillates CAN ensure DIESEL remains liquid, prevent clogging of key components such as pipes, filters and injectors, KEEP fuel system running smoothly. By refining the wax crystals, the pour point depressant can effectively prevent diesel from waxing at low temperatures and further improve the low-temperature fluidity of the oil product. ‌

Cold Flow additives ZX-P2-02 is refined from highly efficient anticoagulant factors, co-solvents, etc. It can quickly mix with diesel, control the formation of paraffin crystals when cooled, significantly reduce the cold filter point and pour point of diesel, further improve the low-temperature fluidity of the oil, and effectively solve the problems caused by sudden temperature drops, cross-regional travel, and low-temperature driving.

Dispersion of low molecular weight olefin in organic solvents

The above listed data represent average values at the time of going to press of this technical information. They are intended as a guide to facilitate handling and cannot be regarded as specified data.. Specified product data are issued as a separate product specification.

Compatibility: Cold flow additives and its dilution are miscible with other Cold flow agents in all proportions.

Performance and Application

Cold Flow additives ZX-P2-02 considerably improves the flow properties of middle distillates at low temperatures. It acts as a crystallization modifier for higher n-paraffins. It prevents the formation of a coherent network for paraffin wax crystals with the result that the cold filter plugging point CFPP and the pour point PP of the middle distillates are considerably reduced.

Cold Flow additives ZX-P2-02 is added to the middle distillates at addition rates of 50 - 100 ppm. The actual injection rate depends on the composition of the middle distillate, which is characterized by the cloud point, the boiling range, the type and the amount of paraffins, and other parameters.

Cold Flow additives ZX-P2-02 is injected directly into the stream of a middle distillate either undiluted or in the form a stock solution. For the injection of the flow improver a temperature of 40 - 50 ℃ is most favorable.

A mixing section adequate length in the pipeline is required. Lines through which undiluted Cold Flow additives ZX-P2-02 is pumped should be heated to 30 - 50 ℃ and the temperature of the middle distillate to be doped should be about 30 - 50℃.

Suitable solvents for preparing Cold Flow additives ZX-P2-02 are middle distillates, kerosene and aromatic hydrocarbons (solvent naphtha).

Performance:

Tested in cold environments, ZX-P2-02 reduces pour point by up to 12°C and improves cold flow properties by 20%, ensuring smooth engine operation even at sub-zero temperatures.

After using ZX-P2-02, we've seen significant improvements in engine startup and fuel efficiency during winter months. The product has reduced maintenance issues caused by fuel blockages.

ZX-P2-02 Cold Flow Additives are ISO 9001 certified and meet international quality standards, ensuring superior performance and reliability."

Storage and handling

Cold flow improver and pour point depressant for middle distillates ZX-P2-02 can be stored up to two years. The storage temperature should not exceed 55 ℃. Short-term exposure to temperature up to 80℃ will not affect the performance of the product.

Packaging

in bulk or in barrel, per clients' request

Safety

When using this product, the information and advice given in our safety data sheet should be observed. Due attention should also be given to the precautions necessary for handling chemicals.

It is industrial use only.

Note

The data contained in this publication are based on our current knowledge and experience. In view of the many factors that may affect processing and application of our product, these data do not relieve processes from carrying out their own investigations and tests; neither do these data imply any guarantee of certain properties, not the solubility of the product for a specific purpose. Any descriptions, drawings, photographs, data, proportions, weights etc. given herein may change with prior information and do not constitute the agreed contractual quality of the product. It is the responsibility of the recipient of our products to ensure that any proprietary rights and existing laws and legislation are observed.

Hot Tags: Cold Flow additives, China Cold Flow additives manufacturers, suppliers, factory, Middle Distillate Cold Flow Improver, cfi trucking, cfi port of loading, CFI and DDP, cfi logistics, cfi export license